Visual 200 Terminal: Difference between revisions
Jump to navigation
Jump to search
Amminadabz (talk | contribs) (Added General info, dissassembly instructions. Instructions are based on the reference manual, I don't have a machine to check against so correct me if I'm wrong.) |
|||
| (4 intermediate revisions by one other user not shown) | |||
| Line 11: | Line 11: | ||
|Input Voltage=120V AC|Power Connector=NEMA 5-15}} | |Input Voltage=120V AC|Power Connector=NEMA 5-15}} | ||
The Visual 200 Terminal is a self-contained terminal based on a Zilog Z-80 processor. It has a detachable keyboard and a 12 inch CRT display. | |||
== Known Issues == | == Known Issues == | ||
| Line 22: | Line 22: | ||
== Disassembly Notes == | == Disassembly Notes == | ||
CRT driver board (TV Monitor Board) is attached to bottom of case with plastic standoffs. Pinch them from the bottom to remove them. | To remove the '''Rear Panel''', remove the two screws at the back of the top cover and the two at the bottom corners of the rear panel. | ||
You may then separate the '''Top Cover'''; it is held on by two screws on each side, under the overhang. Rotate the cover up and slide it off towards the display. | |||
For the '''Logic Board''', first unplug the two cables, the remove the four screws at the corner. You may remove it without removing the top cover. | |||
The '''CRT driver board''' (TV Monitor Board) is attached to bottom of case with four plastic standoffs. Pinch them from the bottom to remove them. | |||
== Original Parts == | == Original Parts == | ||
| Line 47: | Line 53: | ||
|2.2 µF | |2.2 µF | ||
|100 V | |100 V | ||
|Through Hole | |Through Hole Radial | ||
|8mm | |8mm | ||
|12 mm | |12 mm | ||
| Line 61: | Line 67: | ||
|47 µF | |47 µF | ||
|100 V | |100 V | ||
|Through Hole | |Through Hole Radial | ||
|16 mm | |16 mm | ||
|30 mm | |30 mm | ||
| Line 75: | Line 81: | ||
|1000 µF | |1000 µF | ||
|16 V | |16 V | ||
|Through Hole | |Through Hole Radial | ||
|16 mm | |16 mm | ||
|24 mm | |24 mm | ||
| Line 89: | Line 95: | ||
|1 µF | |1 µF | ||
|25 V | |25 V | ||
|Through Hole | |Through Hole Radial | ||
|5 mm | |5 mm | ||
|10 mm | |10 mm | ||
| Line 103: | Line 109: | ||
|4.7 µF | |4.7 µF | ||
|16 V | |16 V | ||
|Through Hole | |Through Hole Radial | ||
|5 mm | |5 mm | ||
|10 mm | |10 mm | ||
| Line 117: | Line 123: | ||
|10 µF | |10 µF | ||
|25 V | |25 V | ||
|Through Hole | |Through Hole Radial | ||
|6 mm | |6 mm | ||
|10 mm | |10 mm | ||
| Line 131: | Line 137: | ||
|22 µF | |22 µF | ||
|25 V | |25 V | ||
|Through Hole | |Through Hole Radial | ||
|8 mm | |8 mm | ||
|12 mm | |12 mm | ||
| Line 145: | Line 151: | ||
|100 µF | |100 µF | ||
|50 V | |50 V | ||
|Through Hole | |Through Hole Radial | ||
|16 mm | |16 mm | ||
|25 mm | |25 mm | ||
| Line 159: | Line 165: | ||
|47 µF | |47 µF | ||
|25 V | |25 V | ||
|Through Hole | |Through Hole Radial | ||
|10 mm | |10 mm | ||
|16 mm | |16 mm | ||
| Line 173: | Line 179: | ||
|4.7 µF | |4.7 µF | ||
|63 V | |63 V | ||
|Through Hole | |Through Hole Radial | ||
|8 mm | |8 mm | ||
|10 mm | |10 mm | ||
| Line 187: | Line 193: | ||
|100 µF | |100 µF | ||
|35 V | |35 V | ||
|Through Hole | |Through Hole Radial | ||
|13 mm | |13 mm | ||
|24 mm | |24 mm | ||
| Line 201: | Line 207: | ||
|1 µF | |1 µF | ||
|100 V | |100 V | ||
|Through Hole | |Through Hole Radial | ||
|8 mm | |8 mm | ||
|12 mm | |12 mm | ||
| Line 215: | Line 221: | ||
|10 µF | |10 µF | ||
|25 V | |25 V | ||
|Through Hole | |Through Hole Radial | ||
|18 mm | |18 mm | ||
|36 mm | |36 mm | ||
| Line 222: | Line 228: | ||
|Bipolar Aluminum Electrolytic | |Bipolar Aluminum Electrolytic | ||
|Nichicon | |Nichicon | ||
|NP-HF | |NP-HF (Non-polar, High Frequency) | ||
|M (±20%) | |M (±20%) | ||
|- | |- | ||
| Line 229: | Line 235: | ||
|4.7 µF | |4.7 µF | ||
|25 V | |25 V | ||
|Through Hole | |Through Hole Radial | ||
|5 mm | |5 mm | ||
|10 mm | |10 mm | ||
| Line 251: | Line 257: | ||
|C307, C313 | |C307, C313 | ||
|2 | |2 | ||
| | |860020672005 / 50YXJ1M5X11 | ||
|[https://www.digikey.com/ Digikey] Mouser LCSC | |[https://www.digikey.com/ Digikey] [https://www.mouser.com/ProductDetail/Wurth-Elektronik/860020672005?qs=0KOYDY2FL29w5cS8aahRvQ%3D%3D Mouser] [https://www.lcsc.com/product-detail/Aluminum-Electrolytic-Capacitors-Leaded_Rubycon-50YXJ1M5X11_C88782.html LCSC] | ||
|- | |- | ||
|C305 | |C305 | ||
|1 | |1 | ||
| | |860020572001 / 860020472001 / 50YXJ4R7MTA5X11 | ||
|[https://www.digikey.com/ Digikey] Mouser LCSC | |[https://www.digikey.com/en/products/detail/w%C3%BCrth-elektronik/860020572001/5727170 Digikey] [https://www.mouser.com/ProductDetail/Wurth-Elektronik/860020472001?qs=0KOYDY2FL2%2F%252BlYkeK95R6A%3D%3D Mouser] [https://www.lcsc.com/product-detail/Aluminum-Electrolytic-Capacitors-Leaded_Rubycon-50YXJ4R7MTA5X11_C365700.html LCSC] | ||
|- | |- | ||
|C309 | |C309 | ||
|1 | |1 | ||
| | |860020572003 / 50YXJ10M5X11 | ||
|[https://www.digikey.com/ Digikey] Mouser LCSC | |[https://www.digikey.com/en/products/detail/w%C3%BCrth-elektronik/860020572003/5727172 Digikey] [https://www.mouser.com/ProductDetail/Wurth-Elektronik/860020572003?qs=0KOYDY2FL28Nvm4U9TAejQ%3D%3D Mouser] [https://www.lcsc.com/product-detail/Aluminum-Electrolytic-Capacitors-Leaded_Rubycon-50YXJ10M5X11_C432355.html LCSC] | ||
|- | |- | ||
|C303 | |C303 | ||
|1 | |1 | ||
| | |860020472004 / 50YXF22MEFCTA5X11 | ||
|[https://www.digikey.com/ Digikey] Mouser LCSC | |[https://www.digikey.com/en/products/detail/w%C3%BCrth-elektronik/860020472004/5727058 Digikey] [https://www.mouser.com/ProductDetail/Wurth-Elektronik/860020472004?qs=0KOYDY2FL29mXlSSkQ%2FGXA%3D%3D Mouser] [https://www.lcsc.com/product-detail/Aluminum-Electrolytic-Capacitors-Leaded_Rubycon-50YXF22MEFCTA5X11_C365695.html LCSC] | ||
|- | |- | ||
|C116 | |C116* (purchase 2 of the listed capacitors) | ||
|1 | |1 | ||
| | |EEU-EE2G100 / 450BXC10MEFC12.5X20 | ||
|[https://www.digikey.com/ Digikey] Mouser LCSC | |[https://www.digikey.com/en/products/detail/panasonic-electronic-components/EEU-EE2G100/1245990 Digikey] [https://www.mouser.com/ProductDetail/Panasonic/EEU-EE2G100?qs=bZLtalHQkT2b1sqwrrSdxA%3D%3D Mouser] [https://www.lcsc.com/product-detail/Aluminum-Electrolytic-Capacitors-Leaded_Rubycon-450BXC10MEFC12-5X20_C473171.html LCSC] | ||
|- | |- | ||
|C109 | |C109 | ||
|1 | |1 | ||
| | |860020572001 / 50PX4R7MEFC5X11 | ||
|[https://www.digikey.com/ Digikey] Mouser LCSC | |[https://www.digikey.com/en/products/detail/w%C3%BCrth-elektronik/860020572001/5727170 Digikey] [https://www.mouser.com/ProductDetail/Wurth-Elektronik/860020572001?qs=0KOYDY2FL29yS9e4FPh3vg%3D%3D Mouser] [https://www.lcsc.com/product-detail/Aluminum-Electrolytic-Capacitors-Leaded_Rubycon-50PX4R7MEFC5X11_C122950.html LCSC] | ||
|} | |} | ||
<nowiki>*</nowiki>This type of capacitor isn't really manufactured anymore and are designed for high frequency low ESR application. According to user ''harmon kardon'' on [https://electronics.stackexchange.com/questions/490707/bipolar-capacitor-replacement-with-very-different-dimension Electrical Engineering Stack Exchange], these types of capacitors should be replaced with 2 of the highest ripple current/voltage-rated polar capacitors in a configuration where the 2 capacitors are soldered into the same space with different polarities (+ of Capacitor A to - of Capacitor B, - of Capacitor A to + of capacitor B). | |||
''If parts are not available or different selection is preferred, you can use the values in the [[#Original_Parts|Original Parts]] section to perform a parametric search.'' | ''If parts are not available or different selection is preferred, you can use the values in the [[#Original_Parts|Original Parts]] section to perform a parametric search.'' | ||
== Related Links == | == Related Links == | ||
[https://doc.lagout.org/science/0_Computer%20Science/0_Computer%20History/old-hardware/visualTechnology/UM200-001-0C_Visual_200_Users_Manual_Mar80.pdf Reference Manual] for service and operation, courtesy of lagout.org. | |||
== References == | == References == | ||
<references /> | <references /> | ||
[[Category:WorkNeeded:OriginalParts]] | |||
[[Category:WorkNeeded:ReplacementParts]] | |||
Latest revision as of 00:58, 9 April 2024
- For more information, see this article's corresponding Wikipedia page: Device.
| This device is in the WorkNeeded:OriginalParts category because it was flagged as missing information on the original parts. It may have replacement parts listed but those cannot be assumed to be identical to the originals. If you have a list of the original parts, please feel free to add them by copying the relevant table from EditorsToolbox:Tables | 
|
| This device is in the WorkNeeded:ReplacementParts category because it was flagged as missing information on replacement parts. If it has the original parts listed you may be able to search for replacements using the parametric searches available from parts distributors. If you have or make a list of replacement parts, please feel free to add them by copying the relevant table from EditorsToolbox:Tables | 
|
Visual 200 Terminal
| Preliminary Information | |
|---|---|
| Release Year | 1980 |
| Leak Risk | High |
| Batteries | None |
| Mounting Technology | Through Hole |
| Capacitor Types | Aluminum Electrolytic, Ceramic |
| Destructive Entry | No |
| Power Requirements | |
| Input Voltage | 120V AC |
| Power Connector | NEMA 5-15 |
The Visual 200 Terminal is a self-contained terminal based on a Zilog Z-80 processor. It has a detachable keyboard and a 12 inch CRT display.
Known Issues
Screen has horizontal distortion
Causes
- Likely failed caps on CRT driver board (TV Monitor Board)
Solutions
- Recap
Disassembly Notes
To remove the Rear Panel, remove the two screws at the back of the top cover and the two at the bottom corners of the rear panel.
You may then separate the Top Cover; it is held on by two screws on each side, under the overhang. Rotate the cover up and slide it off towards the display.
For the Logic Board, first unplug the two cables, the remove the four screws at the corner. You may remove it without removing the top cover.
The CRT driver board (TV Monitor Board) is attached to bottom of case with four plastic standoffs. Pinch them from the bottom to remove them.
Original Parts
CRT driver board (TV Monitor Board)
| RefDes | Qty | Capacitance | Voltage | Mount | Diameter/Size | Height | Lead Spacing | Temp | Type | Brand | Series | Tolerance |
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| C120 | 1 | 2.2 µF | 100 V | Through Hole Radial | 8mm | 12 mm | 5 mm | 105 °C | Aluminum Electrolytic | Nichicon | M (±20%) | |
| C401 | 1 | 47 µF | 100 V | Through Hole Radial | 16 mm | 30 mm | 7.5 mm | 105 °C | Aluminum Electrolytic | Nichicon | M (±20%) | |
| C312 | 1 | 1000 µF | 16 V | Through Hole Radial | 16 mm | 24 mm | 7.5 mm | 105 °C | Aluminum Electrolytic | Nichicon | K (±10%) | |
| C307, C313 | 2 | 1 µF | 25 V | Through Hole Radial | 5 mm | 10 mm | 2.5 mm | 85 °C | Aluminum Electrolytic | Nichicon | M (±20%) | |
| C305 | 1 | 4.7 µF | 16 V | Through Hole Radial | 5 mm | 10 mm | 2.5 mm | 85 °C | Aluminum Electrolytic | Nichicon | K (±10%) | |
| C309 | 1 | 10 µF | 25 V | Through Hole Radial | 6 mm | 10 mm | 4.5 mm | 85 °C | Aluminum Electrolytic | Nichicon | ||
| C303 | 1 | 22 µF | 25 V | Through Hole Radial | 8 mm | 12 mm | 4.5 mm | 85 °C | Aluminum Electrolytic | Nichicon | ||
| C304 | 1 | 100 µF | 50 V | Through Hole Radial | 16 mm | 25 mm | 7.5 mm | 105 °C | Aluminum Electrolytic | Nichicon | M (±20%) | |
| C308 | 1 | 47 µF | 25 V | Through Hole Radial | 10 mm | 16 mm | 5 mm | 105 °C | Aluminum Electrolytic | Nichicon | M (±20%) | |
| C402 | 1 | 4.7 µF | 63 V | Through Hole Radial | 8 mm | 10 mm | 4.5 mm | 105 °C | Aluminum Electrolytic | Nichicon | M (±20%) | |
| C117 | 1 | 100 µF | 35 V | Through Hole Radial | 13 mm | 24 mm | 5 mm | 105 °C | Aluminum Electrolytic | Nichicon | M (±20%) | |
| C121 | 1 | 1 µF | 100 V | Through Hole Radial | 8 mm | 12 mm | 3.5 mm | 105 °C | Aluminum Electrolytic | Nichicon | M (±20%) | |
| C116 | 1 | 10 µF | 25 V | Through Hole Radial | 18 mm | 36 mm | 7.5 mm | 85 °C | Bipolar Aluminum Electrolytic | Nichicon | NP-HF (Non-polar, High Frequency) | M (±20%) |
| C109 | 1 | 4.7 µF | 25 V | Through Hole Radial | 5 mm | 10 mm | 2.5 mm | 85 °C | Aluminum Electrolytic | Nippon/United Chemi-Con | SL |
Replacement Parts
Basic PCB Name
| RefDes | Qty | Compatible Part Number | Order Links |
|---|---|---|---|
| C307, C313 | 2 | 860020672005 / 50YXJ1M5X11 | Digikey Mouser LCSC |
| C305 | 1 | 860020572001 / 860020472001 / 50YXJ4R7MTA5X11 | Digikey Mouser LCSC |
| C309 | 1 | 860020572003 / 50YXJ10M5X11 | Digikey Mouser LCSC |
| C303 | 1 | 860020472004 / 50YXF22MEFCTA5X11 | Digikey Mouser LCSC |
| C116* (purchase 2 of the listed capacitors) | 1 | EEU-EE2G100 / 450BXC10MEFC12.5X20 | Digikey Mouser LCSC |
| C109 | 1 | 860020572001 / 50PX4R7MEFC5X11 | Digikey Mouser LCSC |
*This type of capacitor isn't really manufactured anymore and are designed for high frequency low ESR application. According to user harmon kardon on Electrical Engineering Stack Exchange, these types of capacitors should be replaced with 2 of the highest ripple current/voltage-rated polar capacitors in a configuration where the 2 capacitors are soldered into the same space with different polarities (+ of Capacitor A to - of Capacitor B, - of Capacitor A to + of capacitor B).
If parts are not available or different selection is preferred, you can use the values in the Original Parts section to perform a parametric search.
Related Links
Reference Manual for service and operation, courtesy of lagout.org.