IBM 5160 PSU 240V: Difference between revisions

From Caps Wiki
Jump to navigation Jump to search
VisualWikitext
m (Updated categories)
(Completed original parts table - electrolytics)
Line 37: Line 37:
When connecting the PSU back to the system the mother board power connectors should have the black wires next to each other.
When connecting the PSU back to the system the mother board power connectors should have the black wires next to each other.


The PSU case has security screws in addition to the standard hex/flat screws
The PSU casing has security screws in addition to the standard hex/flat screws


Once the PSU is opened, there are four screws that need to be removed to fully access the main board, in addition to an earth wire and connector from the input board
Once the PSU is opened, there are four screws that need to be removed to fully access the main board, in addition to an earth wire and connector from the input board
Line 66: Line 66:
|25V
|25V
|Through hole (radial)
|Through hole (radial)
|
|7mm
|
|12mm
|
|3mm
|105C
|105C
|Electrolytic
|Electrolytic
|
|Macron
|
|CE-US (4WC?)
|-
|-
|C2 Inrush Limiter sub-board
|C2 Inrush Limiter sub-board
Line 79: Line 79:
|25V
|25V
|Through hole (radial)
|Through hole (radial)
|
|5mm
|
|12mm
|
|2mm
|105C
|105C
|Electrolytic
|Electrolytic
|
|Nichicon
|
|M
|-
|-
|C2, C3 Overcurrent sub-board
|C2, C3 Overcurrent sub-board
Line 92: Line 92:
|50V
|50V
|Through hole (radial)
|Through hole (radial)
|
|5mm
|
|12mm
|
|2mm
|105C
|105C
|Electrolytic
|Electrolytic
|
|KML
|
|
|-
|-
Line 105: Line 105:
|16V
|16V
|Through hole (radial)
|Through hole (radial)
|
|6mm
|
|12mm
|
|3mm
|105C
|Electrolytic
|Nichicon
|M
|-
|C25
|1
|2.2 µF
|50V
|Through hole (radial)
|5mm
|12mm
|2mm
|105C
|105C
|Electrolytic
|Electrolytic
|
|Macron
|
|CE-US (3VC?)
|-
|-
|C10, C29
|C10, C29
Line 118: Line 131:
|16V
|16V
|Through hole (radial)
|Through hole (radial)
|
|5mm
|
|12mm
|
|2mm
|105C
|105C
|Electrolytic
|Electrolytic
|
|Nichicon
|
|M
|-
|-
|C16, C17
|C16, C17
Line 131: Line 144:
|25V
|25V
|Through hole (radial)
|Through hole (radial)
|
|5mm
|
|12mm
|
|2mm
|105C
|105C
|Electrolytic
|Electrolytic
|
|Macron
|
|CE-US (3XC?)
|-
|-
|C27
|C27
Line 144: Line 157:
|16V
|16V
|Through hole (radial)
|Through hole (radial)
|
|5mm
|
|12mm
|
|2mm
|105C
|105C
|Electrolytic
|Electrolytic
|
|Macron
|
|CE-US (3YC?)
|-
|-
|C5, C6
|C5, C6
Line 157: Line 170:
|16V
|16V
|Through hole (radial)
|Through hole (radial)
|
|10mm
|
|16mm
|
|5mm
|105C
|105C
|Electrolytic
|Electrolytic
|
|Macron
|
|CL-US (4WB?)
|-
|-
|C21
|C21
Line 170: Line 183:
|25V
|25V
|Through hole (radial)
|Through hole (radial)
|
|13mm
|
|20mm
|
|5mm
|105C
|105C
|Electrolytic
|Electrolytic
|Nichicon
|Nichicon
|
|M
|-
|-
|C14, C15
|C14, C15
Line 183: Line 196:
|200V
|200V
|Through hole (radial, snap)
|Through hole (radial, snap)
|
|25mm
|
|40mm
|
|10mm
|85C
|85C
|Electrolytic
|Electrolytic
|
|Matsushita
|
|CE
|-
|-
|C9
|C9
Line 196: Line 209:
|25V
|25V
|Through hole (radial)
|Through hole (radial)
|
|16mm
|
|25mm
|
|8mm
|105C
|105C
|Electrolytic
|Electrolytic
|
|KML
|
|M(?)
|-
|-
|C7, C8
|C7, C8
Line 209: Line 222:
|10V
|10V
|Through hole (radial)
|Through hole (radial)
|
|16mm
|
|25mm
|
|8mm
|105C
|105C
|Electrolytic
|Electrolytic
|
|Matsushita
|
|CE GM
|-
|-
|C11
|C11
Line 222: Line 235:
|16V
|16V
|Through hole (radial)
|Through hole (radial)
|
|18mm
|
|35mm
|
|8mm
|105C
|105C
|Electrolytic
|Electrolytic
|Macron
|Macron
|CE-US
|CE-US (4PB?)
|}
|}


Revision as of 11:40, 13 May 2024

For more information, see this article's corresponding Wikipedia page: IBM Personal Computer XT.

Released as the IBM Personal Computer XT, or PC/XT, the 5160 is based around Intel's 8088 processor featuring 8-bit ISA slots for expansion cards. It came with one 5.25" floppy drive, and one 5.25" full height HDD most commonly 10MB. The PC/XT used a 130W power supply.


Preliminary Information
Leak Risk Low
Batteries None
Destructive Entry No


Known Issues

No Power

Causes

  • Power supply will not turn on

Solutions

  • Power supply must have a load on it to activate
  • Recap

Disassembly Notes

The top shell must be tiled up when pulled all the way forward to release.

Watch out for the speaker on the left side when sliding the shell

The top rear screw tab may catch on the PSU and cable (lift rear when sliding avoid)

PSU slides into tabs in bottom shell

When connecting the PSU back to the system the mother board power connectors should have the black wires next to each other.

The PSU casing has security screws in addition to the standard hex/flat screws

Once the PSU is opened, there are four screws that need to be removed to fully access the main board, in addition to an earth wire and connector from the input board

There are three sub-boards attached to the main PSU board that generally do not need to be removed to access all the caps

Original Parts

Basic PCB Name

Capacitor Specifications and Footprint Information
RefDes Qty Capacitance Voltage Mount Diameter/Size Height Lead Spacing Temp Type Brand Series
C1 Inrush Limiter sub-board 1 100 µF 25V Through hole (radial) 7mm 12mm 3mm 105C Electrolytic Macron CE-US (4WC?)
C2 Inrush Limiter sub-board 1 3.3µF 25V Through hole (radial) 5mm 12mm 2mm 105C Electrolytic Nichicon M
C2, C3 Overcurrent sub-board 2 1 µF 50V Through hole (radial) 5mm 12mm 2mm 105C Electrolytic KML
C3001 Voltage Limiter sub-board 1 47 µF 16V Through hole (radial) 6mm 12mm 3mm 105C Electrolytic Nichicon M
C25 1 2.2 µF 50V Through hole (radial) 5mm 12mm 2mm 105C Electrolytic Macron CE-US (3VC?)
C10, C29 2 10 µF 16V Through hole (radial) 5mm 12mm 2mm 105C Electrolytic Nichicon M
C16, C17 2 10 µF 25V Through hole (radial) 5mm 12mm 2mm 105C Electrolytic Macron CE-US (3XC?)
C27 1 22 µF 16V Through hole (radial) 5mm 12mm 2mm 105C Electrolytic Macron CE-US (3YC?)
C5, C6 2 330 µF 16V Through hole (radial) 10mm 16mm 5mm 105C Electrolytic Macron CL-US (4WB?)
C21 1 470 µF 25V Through hole (radial) 13mm 20mm 5mm 105C Electrolytic Nichicon M
C14, C15 2 470 µF 200V Through hole (radial, snap) 25mm 40mm 10mm 85C Electrolytic Matsushita CE
C9 1 1000 µF 25V Through hole (radial) 16mm 25mm 8mm 105C Electrolytic KML M(?)
C7, C8 2 2200 µF 10V Through hole (radial) 16mm 25mm 8mm 105C Electrolytic Matsushita CE GM
C11 1 4700 µF 16V Through hole (radial) 18mm 35mm 8mm 105C Electrolytic Macron CE-US (4PB?)

Replacement Parts

Basic PCB Name

Capacitors
RefDes Qty Compatible Part Number Order Links
Digikey

If parts are not available or different selection is preferred, you can use the values in the Original Parts section to perform a parametric search.

Related Links

See https://minuszerodegrees.net/5160/psu/5160_psu.htm for additional information

See https://minuszerodegrees.net/5150_5160/MDC/minimum_diag_config.htm for how to confirm faulty PSU

References

Retrieved from "https://caps.wiki/index.php?title=IBM_5160_PSU_240V&oldid=5122"