IBM 5160 PSU 240V

For more information, see this article's corresponding Wikipedia page: IBM Personal Computer XT.

Released as the IBM Personal Computer XT, or PC/XT, the 5160 is based around Intel's 8088 processor featuring 8-bit ISA slots for expansion cards. It came with one 5.25" floppy drive, and one 5.25" full height HDD most commonly 10MB. The PC/XT used a 130W power supply.

IBM Personal Computer XT (PC/XT)

Preliminary Information
Release Year	1983
Leak Risk	Low
Batteries	None
Capacitor Types	Aluminium Electrolytic, Tantalum, Ceramic
Destructive Entry	No

Known Issues

No Power

Power supply will not turn on.

	Causes	Solutions
1	No load.	Power supply must have a load on it to activate. See https://minuszerodegrees.net/5150_5160/MDC/minimum_diag_config.htm for details, or build a test harness that loads the +5V and +12V outputs before assuming the PSU is itself at fault. See https://www.minuszerodegrees.net/5160/psu/5160_psu_line_ratings.htm for guidance on maximum loads.
2	The PSU has inbuilt protections to disable its LV outputs if the downstream boards are shorted.	Check the downstream boards for shorts. There's plenty of info about the tantalum caps on the XT motherboard being a major cause of this. See https://minuszerodegrees.net
3	Electrolytic caps failing/failed.	Recap the electrolytics using the parts list below
4	RIFA caps failed.	Some PSU variations used RIFA caps at C1 and C2 on the AC input board which will fail rather aggressively. Always replace if present, failed or not.

Disassembly Notes

External Casing:

• The external casing of the PC is held in place by five 1/4" hexagonal screws on the back plate. One in each corner and one in the top centre.
• The external casing must be tilted up when pulled all the way forward to release.
• Watch out for the speaker on the left side when sliding the casing.
• The centre screw tab may catch on the PSU and cable (lift rear of case when sliding avoid).

PSU Removal and access:

• PSU is held by four 1/4" hex screws to rear of PC case and two slides on bottom of PC case and needs to be slid toward front of PC to release.
• The PSU case has two Torx T15H security screws in addition to the standard 1/4" hex screws.
• When connecting the PSU back to the system the mother board power connectors P8 and P9 should have the black wires next to each other.

PSU internal disassembly:

• Once the PSU is opened, there are four 1/4" hex screws that need to be undone to fully remove the main board, in addition to an earth wire and connector from the AC input board.
• There are three sub-boards attached to the main PSU board that generally do not need to be disassembled to access all the electrolytic caps.
• If there are RIFAs on the AC input board then that will also need to be removed from the main PSU case.

Original Parts

130W Power Supply Main Board

204-1071-03

• 

  PSU example 1

• 

  PSU example 1 board identifiers

• 

  Decapped PSU example 1

• 

  C3 on overcurrent sub-board (reversed polarity?). See note 2.

• 

  PSU example 2

Notes:

1. In the two PSU examples shown here, the three sub-boards extending towards the camera are left Voltage Windows, centre Overcurrent Monitor, right Inrush Limiter
2. The polarity of the C3 cap on the Overcurrent sub-board appears to be marked incorrectly on the board. See picture above. Check and confirm before removing/replacing. Presumably the PSU functioned correctly for most of its life and the manufacturer knew to ignore the polarity marking for this cap.
3. Capacitor designations are repeated on the sub-boards. i.e. there are multiple capacitors with a C1 designation printed on the different boards in the PSU etc.

Capacitor Specifications and Footprint Information

RefDes	Qty	Capacitance	Voltage	Mount	Diameter/Size	Height	Lead Spacing	Temp	Type	Brand	Series
C1 Inrush Limiter sub-board	1	100 µF	25V	Through hole (radial)	7mm	12mm	3mm	105C	Electrolytic	Marcon	CE-US (4WC?)
C2 Inrush Limiter sub-board	1	3.3µF	25V	Through hole (radial)	5mm	12mm	2mm	105C	Electrolytic	Nichicon	M
C2, C3 (see note 2 above) Overcurrent sub-board	2	1 µF	50V	Through hole (radial)	5mm	12mm	2mm	105C	Electrolytic	KML
C3001 Voltage Window sub-board	1	47 µF	16V	Through hole (radial)	6mm	12mm	3mm	105C	Electrolytic	Nichicon	M
C25	1	2.2 µF	50V	Through hole (radial)	5mm	12mm	2mm	105C	Electrolytic	Marcon	CE-US (3VC?)
C10, C29	2	10 µF	16V	Through hole (radial)	5mm	12mm	2mm	105C	Electrolytic	Nichicon	M
C16, C17	2	10 µF	25V	Through hole (radial)	5mm	12mm	2mm	105C	Electrolytic	Marcon	CE-US (3XC?)
C27	1	22 µF	16V	Through hole (radial)	5mm	12mm	2mm	105C	Electrolytic	Marcon	CE-US (3YC?)
C5, C6	2	330 µF	16V	Through hole (radial)	10mm	16mm	5mm	105C	Electrolytic	Marcon	CL-US (4WB?)
C21	1	470 µF	25V	Through hole (radial)	13mm	20mm	5mm	105C	Electrolytic	Nichicon	M
C14, C15	2	470 µF	200V	Through hole (radial, snap)	25mm	40mm	10mm	85C	Electrolytic	Matsushita	CE
C9	1	1000 µF	25V	Through hole (radial)	16mm	25mm	8mm	105C	Electrolytic	KML	M(?)
C7, C8	2	2200 µF	10V	Through hole (radial)	16mm	25mm	8mm	105C	Electrolytic	Matsushita	CE GM
C11	1	4700 µF	16V	Through hole (radial)	18mm	35mm	8mm	105C	Electrolytic	Marcon	CE-US (4PB?)
C1, C2 - AC input board	2	0.1uF	?	?	?			?	RIFA paper	...any...

Replacement Parts

130W Power Supply Main Board

Element14 is the Australian distributor previously known as Farnell.

Important Note: I put this list together using the local Element14 website for Australia however after ordering I rapidly become aware they don't have a lot of local stock. Despite selecting the option for the shipment to be delivered as a single package once they had received the overseas components, Element14 shipped the Australian, US and UK stocked items separately, thereby tripling the postage. In addition, they didn't have one item that was listed as stocked thereby forcing me to source from another outlet thus incurring even more postage. Their after-sales service sent me emails that were demonstrably untrue and they ignored my repeated request to consolidate the remaining two packages after the first one had shipped with a single $1 cap. I ended up paying around $60 postage for $37 worth of caps. I suspect their business model is to make money on postage as the margins on caps must be pretty thin. I can not recommend them as a source of caps in Australia.

Capacitors

RefDes	Qty	Compatible Part Number	Order Links
C1 Inrush Limiter sub-board	1	PANASONIC  EEUFM1H101BJ	DigiKey Mouser Element14
C2 Inrush Limiter sub-board	1	PANASONIC EEUEB1H3R3S	DigiKey Mouser Element14
C2, C3 Overcurrent sub-board	2	RUBYCON 50YXF1MEFC5X11	DigiKey Mouser Element14
C3001 Voltage Limiter sub-board	1	PANASONIC ECA1CHG470	DigiKey Mouser Element14
C25	1	PANASONIC EEUEB1H2R2S	DigiKey Mouser Element14
C10, C29, C16, C17	4	PANASONIC EEAFC1E100	DigiKey Mouser RS Online
C27	1	PANASONIC ECA1CHG220	DigiKey Mouser Element14
C5, C6	2	PANASONIC EEUFC1E331B	DigiKey Mouser Element14
C21	1	PANASONIC EEUEB1H471	DigiKey Mouser Element14
C14, C15	2	Nichicon LLS2D471MELZ	DigiKey Mouser Element14
C9	1	PANASONIC EEUFC1E102SB	DigiKey Mouser Element14
C7, C8	2	PANASONIC EEUFK1C222S	DigiKey Mouser Element14
C11	1	PANASONIC EEUFK1C472S	DigiKey Mouser Element14
C1, C2 - AC Inpout board	2	?	?

If parts are not available or different selection is preferred, you can use the values in the Original Parts section to perform a parametric search.

Related Links

See https://minuszerodegrees.net/5160/psu/5160_psu.htm for additional information

See https://minuszerodegrees.net/5150_5160/MDC/minimum_diag_config.htm for how to confirm faulty PSU

See https://slx-online.biz/hursley/docs/5155_psu.pdf by Dr H.Holden for a comprehensive breakdown of a 5155 PSU that is very similar. This is absolute gold.