Chauvet Strike 1: Difference between revisions

From Caps Wiki
Jump to navigation Jump to search
mNo edit summary
m (Change category.)
 
(7 intermediate revisions by the same user not shown)
Line 1: Line 1:
{{DeviceAlerts}}The Chauvet STRIKE 1 is an outdoor-ready blinder powered by an intense 230 W warm white LED source. It is also an awesome strobe and a wide area floodlight. Its IP rated fan keeps it cool enough for use as a wash while IP rated direct power and DMX connections eliminate undesirable whips. An emulated “amber shift” warms the Colour Temperature of the light as it dims to mimic incandescent lights perfectly.
{{DeviceAlerts}}The Chauvet STRIKE 1 is an outdoor rated blinder powered by a 230 W warm white LED source. It is also a strobe and a wide area floodlight.
==Known Issues==
==Known Issues==
===Symptom or Problem Encountered===
===Symptom or Problem Encountered===
Non functioning light. No display on the control panel.
Non functioning light. No display on the control panel.


I was told it's the PSU. It wasn't.
I was told it's a failed PSU. It wasn't.
====Causes====
====Causes====
*Shorted diode on controller board.
*Shorted diode on controller board.
Line 25: Line 25:
Replacing the diode fixed the fault. But as to what caused the failure in the first place?
Replacing the diode fixed the fault. But as to what caused the failure in the first place?


I repaired two of these with identical faults.
Two of these lamps had identical faults.
== Re-assembly ==
Make sure the seal is seated correctly as you re-seat the module.
 
Do not over tighten the screws, bearing in mind that the threads in the aluminium are relatively soft and possibly already damaged by corrosion.
 
Use some anti-seize compound if you have any. A light greasing may help to prevent further corrosion but can aggravate over tightening.
==Original Parts==
==Original Parts==
===Basic PCB Name===
===Basic PCB Name===
Line 36: Line 42:
!Current  
!Current  
![https://caps.wiki/wiki/Part_Footprints Mount]
![https://caps.wiki/wiki/Part_Footprints Mount]
!Diameter/Size
!Footprint
|-
|-
|SS310
|SS310
Line 43: Line 49:
|3A
|3A
|SMD
|SMD
|DO214
|DO214AC
|}
|}
==Replacement Parts==
==Replacement Parts==
Line 52: Line 58:
!Description
!Description
!Compatible Part Number
!Compatible Part Number
!Order Links
|-
|-
|SS310
|SS310
|1
|1
|Schottky Diode 100V 3A
|Schottky Diode 100V 3A
|
|HY Electronic Corp SS310A
|
|}
|}
''If parts are not available or different selection is preferred, you can use the values in the [[#Original_Parts|Original Parts]] section to perform a parametric search.''
''If parts are not available or different selection is preferred, you can use the values in the [[#Original_Parts|Original Parts]] section to perform a parametric search.''
==References==
==References==
<references />
<references />
[[Category:WorkNeeded:ReplacementParts]]
[[Category:Lighting]]
[[Category:Lighting:Stage theatre]]
[[Category:Stage, theatre]]

Latest revision as of 09:54, 25 March 2024

The Chauvet STRIKE 1 is an outdoor rated blinder powered by a 230 W warm white LED source. It is also a strobe and a wide area floodlight.

Known Issues

Symptom or Problem Encountered

Non functioning light. No display on the control panel.

I was told it's a failed PSU. It wasn't.

Causes

  • Shorted diode on controller board.

Solutions

  • Replace a £0.60 diode.

Disassembly Notes

These are outdoor lights and the cap head screws may have corrosion in the aluminium housing. Use penetrating oil if possible.

Remove the three cap head screws holding the display and control panel housing taking care to retain the washers.

The panel assembly will lift out. If the fault is as described the connectors can remain undisturbed. Some of the zip ties had sharp pointy ends, so take care with those.

Controller board showing faulty diode.

Diagnosis

Without mains power connected check for a short across D2, adjacent to the inductor.

If short, lift one side of the diode (or remove it completely) and check the diode and the solder pads. In my case the short on the board went away.

If that's not the the fault, plug in the mains power and check the DC voltage into the board. The voltage to the board is 63V DC.

Replacing the diode fixed the fault. But as to what caused the failure in the first place?

Two of these lamps had identical faults.

Re-assembly

Make sure the seal is seated correctly as you re-seat the module.

Do not over tighten the screws, bearing in mind that the threads in the aluminium are relatively soft and possibly already damaged by corrosion.

Use some anti-seize compound if you have any. A light greasing may help to prevent further corrosion but can aggravate over tightening.

Original Parts

Basic PCB Name

Controller board.

Diode Specifications and Footprint Information
RefDes Qty Voltage Current Mount Footprint
SS310 1 100 3A SMD DO214AC

Replacement Parts

Diode
RefDes Qty Description Compatible Part Number
SS310 1 Schottky Diode 100V 3A HY Electronic Corp SS310A

If parts are not available or different selection is preferred, you can use the values in the Original Parts section to perform a parametric search.

References