Simpson SWT954: Difference between revisions
Jump to navigation
Jump to search
m (→Causes: Add image) |
|||
| Line 18: | Line 18: | ||
File:Simpson-swt954-tny278pn-macro-thermal-before.jpg|Macro thermal image of over-temperature U8 (TNY278PN) | File:Simpson-swt954-tny278pn-macro-thermal-before.jpg|Macro thermal image of over-temperature U8 (TNY278PN) | ||
</gallery> | </gallery> | ||
====Solutions==== | ====Solutions==== | ||
*Replace SMPS U9 TNY278PN | *Replace SMPS U9 TNY278PN | ||
| Line 72: | Line 71: | ||
|1 | |1 | ||
|TNY278PN | |TNY278PN | ||
|[https://www.digikey.com/en/products/detail/power-integrations/TNY278PN/1007187 | |[https://www.digikey.com/en/products/detail/power-integrations/TNY278PN/1007187 DigiKey] [https://www.mouser.com/ProductDetail/Power-Integrations/TNY278PN?qs=WS5Jv%252B%252Bx1qVYqb4HOX%252BBag%3D%3D Mouser] | ||
|} | |} | ||
''If parts are not available or different selection is preferred, you can use the values in the [[#Original_Parts|Original Parts]] section to perform a parametric search'' | ''If parts are not available or different selection is preferred, you can use the values in the [[#Original_Parts|Original Parts]] section to perform a parametric search'' | ||
Revision as of 00:04, 14 April 2023
| This device is in the WorkNeeded:ReplacementParts category because it was flagged as missing information on replacement parts. If it has the original parts listed you may be able to search for replacements using the parametric searches available from parts distributors. If you have or make a list of replacement parts, please feel free to add them by copying the relevant table from EditorsToolbox:Tables | 
|
Simpson SWT954
| Preliminary Information | |
|---|---|
| Release Year | 2010 |
| Leak Risk | Low |
| Batteries | None |
| Mounting Technology | Through Hole, SMD |
| Capacitor Types | Aluminum Electrolytic, Ceramic, Film |
| Destructive Entry | No |
The Simpson SWT954 is a 9.5 kg top load washing machine (Electrolux design rebranded as Simpson with minor changes).
Known Issues
Unit turns off after being powered on for a couple minutes
Causes
- Off-line SMPS IC has partially failed and is tripping it's internal over-temperature cut-off
-
Macro thermal image of over-temperature U8 (TNY278PN)
Solutions
- Replace SMPS U9 TNY278PN
Unit will shake excessively during cycle and stop with error code 'E17' and four beeps
Causes & solutions
- Unit is overloaded: ensure weight of load is less than your model's limit
- Load is imbalanced: redistribute load to be more balanced
- Bowl springs have failed or become loose: replace or re-tighten
- Out of balance detection switch is not aligned correctly: replace or re-align
Disassembly Notes
 WARNING This device contains a non-isolated mains voltage buck switch mode power supply. Low voltage circuity still poses a shock hazard. |
- This device is designed well with service and repair in mind
- The manufacturer has published exploded assembly diagrams showing all fasteners and components (See 'EX. VIEW DRAWING 7696' for SWT954)
- The front control panel bezel is held on with two screws at the back of the unit
- The power supply and motor drive PCB is removed with two screws and unclipped from the plastic holder
Original Parts
Power supply and motor drive PCB
HT-PCB-140-08058A-P-V06
-
Top
-
Bottom
WARNING Capacitor C22 is 400 V 470 µF (37.6 J), it does not have a bleed resistor.
| RefDes | Qty | Part Number | Brand | Series | Mount | Footprint | Failure Mode |
|---|---|---|---|---|---|---|---|
| U8 | 1 | TNY278PN | Power Integrations | TinySwitch-III | THT | 8-PDIP-C | Silicon damage causes IC to overheat and go into thermal shutdown |
Replacement Parts
Power supply and motor drive PCB
| RefDes | Qty | Compatible Part Number | Order Links |
|---|---|---|---|
| U8 | 1 | TNY278PN | DigiKey Mouser |
If parts are not available or different selection is preferred, you can use the values in the Original Parts section to perform a parametric search