Chauvet Strike 1: Difference between revisions

Latest revision as of 09:54, 25 March 2024

The Chauvet STRIKE 1 is an outdoor rated blinder powered by a 230 W warm white LED source. It is also a strobe and a wide area floodlight.

Known Issues

Symptom or Problem Encountered

Non functioning light. No display on the control panel.

I was told it's a failed PSU. It wasn't.

Causes

Shorted diode on controller board.

Solutions

Replace a £0.60 diode.

Disassembly Notes

These are outdoor lights and the cap head screws may have corrosion in the aluminium housing. Use penetrating oil if possible.

Remove the three cap head screws holding the display and control panel housing taking care to retain the washers.

The panel assembly will lift out. If the fault is as described the connectors can remain undisturbed. Some of the zip ties had sharp pointy ends, so take care with those.

Diagnosis

Without mains power connected check for a short across D2, adjacent to the inductor.

If short, lift one side of the diode (or remove it completely) and check the diode and the solder pads. In my case the short on the board went away.

If that's not the the fault, plug in the mains power and check the DC voltage into the board. The voltage to the board is 63V DC.

Replacing the diode fixed the fault. But as to what caused the failure in the first place?

Two of these lamps had identical faults.

Re-assembly

Make sure the seal is seated correctly as you re-seat the module.

Do not over tighten the screws, bearing in mind that the threads in the aluminium are relatively soft and possibly already damaged by corrosion.

Use some anti-seize compound if you have any. A light greasing may help to prevent further corrosion but can aggravate over tightening.

Original Parts

Basic PCB Name

Controller board.

Diode Specifications and Footprint Information
RefDes	Qty	Voltage	Current	Mount	Footprint
SS310	1	100	3A	SMD	DO214AC

Replacement Parts

Diode
RefDes	Qty	Description	Compatible Part Number
SS310	1	Schottky Diode 100V 3A	HY Electronic Corp SS310A

If parts are not available or different selection is preferred, you can use the values in the Original Parts section to perform a parametric search.

References

@@ Line 1: / Line 1: @@
-{{WikipediaInfoAlt|Device}}
+{{DeviceAlerts}}The Chauvet STRIKE 1 is an outdoor rated blinder powered by a 230 W warm white LED source. It is also a strobe and a wide area floodlight.
-{{DeviceAlerts}}
-{{InfoboxDevice
-|Title = New Device
-|Picture =
-|Release Year = 1980
-|Mounting Technology = Through Hole, SMD, BGA, Sockets
-|Capacitor Types = Aluminum Electrolytic, Tantalum, Ceramic, Polymer
-|Leak Risk = Medium
-|Batteries = None
-|Destructive Entry = No
-}}
-This is a template page for creating new pages for devices, troubleshooting them, part lists, and other repair info.
 ==Known Issues==
 ===Symptom or Problem Encountered===
+Non functioning light. No display on the control panel.
+I was told it's a failed PSU. It wasn't.
 ====Causes====
-*Non functioning light. I was told it's the PSU. It wasn't.
+*Shorted diode on controller board.
 ====Solutions====
 *Replace a £0.60 diode.
 ==Disassembly Notes==
 These are outdoor lights and the cap head screws may have corrosion in the aluminium housing. Use penetrating oil if possible.
-Remove the three cap head screws holding the display and control panel housing.
+Remove the three cap head screws holding the display and control panel housing taking care to retain the washers.
+The panel assembly will lift out. If the fault is as described the connectors can remain undisturbed. Some of the zip ties had sharp pointy ends, so take care with those.
+[[File:Controller board.jpg|thumb|Controller board showing faulty diode.]]
+== Diagnosis ==
+Without mains power connected check for a short across D2, adjacent to the inductor.
+If short, lift one side of the diode (or remove it completely) and check the diode and the solder pads. In my case the short on the board went away.
+If that's not the the fault, plug in the mains power and check the DC voltage into the board. The voltage to the board is 63V DC.
+Replacing the diode fixed the fault. But as to what caused the failure in the first place?
+Two of these lamps had identical faults.
+== Re-assembly ==
+Make sure the seal is seated correctly as you re-seat the module.
+Do not over tighten the screws, bearing in mind that the threads in the aluminium are relatively soft and possibly already damaged by corrosion.
+Use some anti-seize compound if you have any. A light greasing may help to prevent further corrosion but can aggravate over tightening.
 ==Original Parts==
 ===Basic PCB Name===
-''Note model numbers and board revisions here''
+Controller board.
 {| class="wikitable sortable"
 |+Diode [[Capacitor Specifications|Specifications]] and [[Part Footprints|Footprint]] Information
@@ Line 32: / Line 42: @@
 !Current
 ![https://caps.wiki/wiki/Part_Footprints Mount]
-!Diameter/Size
+!Footprint
-!Height
-!Temp
-![https://caps.wiki/wiki/Capacitor_Types Type]
-!Brand
-!Series
 |-
-|
+|SS310
 |1
 |100
 |3A
-|
+|SMD
-|
+|DO214AC
-|
-|0 °C
-|
-|
-|
 |}
 ==Replacement Parts==
-===Basic PCB Name===
 {| class="wikitable sortable"
 |+Diode
 !RefDes
 !Qty
+!Description
 !Compatible Part Number
-!Order Links
 |-
-|
+|SS310
 |1
-|
+|Schottky Diode 100V 3A
-|
+|HY Electronic Corp SS310A
 |}
 ''If parts are not available or different selection is preferred, you can use the values in the [[#Original_Parts|Original Parts]] section to perform a parametric search.''
-===Kits===
-*
-==Related Links==
-*[https://www.youtube.com Videos or other things that might be helpful to check out]
 ==References==
 <references />
-[[Category:WorkNeeded:General]]
-[[Category:WorkNeeded:ReplacementParts]]
 [[Category:Lighting]]
+[[Category:Stage, theatre]]