Part Footprints: Difference between revisions

From Caps Wiki
Jump to navigation Jump to search
No edit summary
(Add example PCB image)
 
(One intermediate revision by the same user not shown)
Line 1: Line 1:
[[File:Caps-Wiki-Example-PCB.png|thumb|A render of a variety of common SMT and THT component packages.]]
If you have decided a capacitor is bad and want to replace it you'll need to not only get one of similar electrical value, but also physical dimensions. Through hole, SMD, and rectangular SMD parts are all measured physically in different ways however. Knowing how to measure them will make getting proper fitting replacements much easier. I highly recommend getting a set of calipers to measure with instead of using something like a ruler. Inexpensive digital calipers will be good enough for most measurements you need to make.
If you have decided a capacitor is bad and want to replace it you'll need to not only get one of similar electrical value, but also physical dimensions. Through hole, SMD, and rectangular SMD parts are all measured physically in different ways however. Knowing how to measure them will make getting proper fitting replacements much easier. I highly recommend getting a set of calipers to measure with instead of using something like a ruler. Inexpensive digital calipers will be good enough for most measurements you need to make.


== Through Hole ==
== Through Hole ==
[[File:Tht_radial.jpg|thumb|upright=0.5|Through hole radial capacitor and accompanying PCB footprint. ]]
The most important measurement for through hole parts is the "pitch" which is the distance between the pins. This is measured directly from one pin to the other. Radial capacitors also need their diameter and height measured. You can probably get away with a different height but it can matter if it's a complex and densely packed device. The size of the diameter and the pitch of the pins aren't always guaranteed to be related but there are common size and shape capacitors where these values are likely to be used by many parts. The height can vary a lot more.
The most important measurement for through hole parts is the "pitch" which is the distance between the pins. This is measured directly from one pin to the other. Radial capacitors also need their diameter and height measured. You can probably get away with a different height but it can matter if it's a complex and densely packed device. The size of the diameter and the pitch of the pins aren't always guaranteed to be related but there are common size and shape capacitors where these values are likely to be used by many parts. The height can vary a lot more.


Line 7: Line 9:


== SMD ==
== SMD ==
[[File:smd_radial.jpg|thumb|upright=0.5|Surface mount radial capacitor and accompanying PCB footprint. ]]
For can type SMD caps you really only need to worry about the diameter, the position of the pads is always relative to that. These are much more standardized for the size and the pads are usually slightly oversized on a PCB and can accommodate slightly different parts. The height still needs to be checked but these capacitors are usually shorter.
For can type SMD caps you really only need to worry about the diameter, the position of the pads is always relative to that. These are much more standardized for the size and the pads are usually slightly oversized on a PCB and can accommodate slightly different parts. The height still needs to be checked but these capacitors are usually shorter.


== Rectangular SMD ==
== Rectangular SMD ==
[[File:smd_chip.jpg|thumb|upright=0.5|Surface mount chip capacitors. ]]
There are specific standard sizes for these parts. One of the most common for example is 0603, but these come in metric and imperial sizes. These sizes can be cross referenced between the two so you can get all sizes available in either. It is possible to measure these and look up what the sizes are, you will want to use a look up table to determine what size code your part is. There are also physical guides you can get to hold them up against to instantly see the size. They are different enough that if you work with enough of them you'll be able to recognize the sizes by eye eventually.
There are specific standard sizes for these parts. One of the most common for example is 0603, but these come in metric and imperial sizes. These sizes can be cross referenced between the two so you can get all sizes available in either. It is possible to measure these and look up what the sizes are, you will want to use a look up table to determine what size code your part is. There are also physical guides you can get to hold them up against to instantly see the size. They are different enough that if you work with enough of them you'll be able to recognize the sizes by eye eventually.
__FORCETOC__
__FORCETOC__
[[Category:Information]]
[[Category:Information]]

Latest revision as of 08:11, 8 February 2022

A render of a variety of common SMT and THT component packages.

If you have decided a capacitor is bad and want to replace it you'll need to not only get one of similar electrical value, but also physical dimensions. Through hole, SMD, and rectangular SMD parts are all measured physically in different ways however. Knowing how to measure them will make getting proper fitting replacements much easier. I highly recommend getting a set of calipers to measure with instead of using something like a ruler. Inexpensive digital calipers will be good enough for most measurements you need to make.

Through Hole

Through hole radial capacitor and accompanying PCB footprint.

The most important measurement for through hole parts is the "pitch" which is the distance between the pins. This is measured directly from one pin to the other. Radial capacitors also need their diameter and height measured. You can probably get away with a different height but it can matter if it's a complex and densely packed device. The size of the diameter and the pitch of the pins aren't always guaranteed to be related but there are common size and shape capacitors where these values are likely to be used by many parts. The height can vary a lot more.

You may find when ordering replacements that you can only find smaller sizes than when you are removing. As long as you are able to match the electrical values this won't matter too much as the pins coming from the capacitors can be bent out a bit to compensate for this.

SMD

Surface mount radial capacitor and accompanying PCB footprint.

For can type SMD caps you really only need to worry about the diameter, the position of the pads is always relative to that. These are much more standardized for the size and the pads are usually slightly oversized on a PCB and can accommodate slightly different parts. The height still needs to be checked but these capacitors are usually shorter.

Rectangular SMD

Surface mount chip capacitors.

There are specific standard sizes for these parts. One of the most common for example is 0603, but these come in metric and imperial sizes. These sizes can be cross referenced between the two so you can get all sizes available in either. It is possible to measure these and look up what the sizes are, you will want to use a look up table to determine what size code your part is. There are also physical guides you can get to hold them up against to instantly see the size. They are different enough that if you work with enough of them you'll be able to recognize the sizes by eye eventually.